Match UP 10DSP
Match UP 10DSP
Match UP 10DSP
Match UP 10DSP
Match UP 10DSP
Match UP 10DSP
Match UP 10DSP
Match UP 10DSP
Match UP 10DSP
Match UP 10DSP
Match

Match UP 10DSP

Match UP 10DSP

10 channel amp, 11 channel DSP, with 8 x 65 Watts + 2 x 90 Watts (4 Ohms)

Powerhouse in a compact format

Despite its huge output power of 8 x 65 Watts at 4 Ohms and 2 x 90 / 160 Watts at 4 / 2 Ohms at the Sub Outs, as well as the enormous feature set, the UP 10DSP comes in an extremely compact design, so that installation is possible even in confined spaces.

Features

  • Ultra efficient 10-channel amplifier with 1-channel line output and 11-channel DSP
  • Perfect for upgrading multi-channel factory sound systems
  • Optional cable harnesses for easy integration into existing multi-channel factory sound systems
  • Extremely powerful 64 Bit “fixed point” Audio DSP
  • ACO – Advanced 32 Bit CoProcessor platform for system and DSP features like:
    • ISA (Input Signal Analyzer) and InputEQ for easy analysis and compensation of input signals
    • SFX sound effects – Augmented Bass Processing, StageXpander, RealCenter & Co.
  • High power 8-channel highlevel input with ADEP.3 circuit – two channels with up to 32 V RMS input sensitivity
  • 1:1 IOR (Input-to-Output Routing) in combination with the optional MEC ANALOG IN module – same number of highlevel inputs and amplifier outputs
  • VCP (Virtual Channel Processing) allows even more flexible configuration for highly complex sound systems
  • MATCH Extension Card slot (MEC) for additional input / output modules like Bluetooth® Audio Streaming, High Resolution Audio Streaming via USB etc.
  • Optical input in SPDIF format with sampling rate between 12 and 96 kHz
  • Mono RCA output for the connection of an external amplifier e.g. subwoofer amplifier
  • SCP (Smart Control Port) for optional accessory like DIRECTOR, CONDUCTOR & Co.
  • Auto Remote switch
  • Start-Stop capability down to 6 Volts supply voltage
  • Compact design with low heat dissipation thanks to extraordinary efficiency

Technical data

  UP 10DSP
Output power RMS  
- @ 4 Ohms Channels A - H: 8 x 65 Watts
- @ 2 Ohms -
- @ 1 Ohm -
- bridged @ 4 Ohms -
- bridged @ 2 Ohms -
- Subwoofer output @ 4 Ohms Channels I - J: 2 x 90 Watts
- Subwoofer output @ 2 Ohms Channels I - J: 2 x 160 Watts
Amplifier technology Class GD
Inputs 8 x Highlevel speaker input
1 x Optical SPDIF (12 - 96 kHz)
1 x Remote In
Input sensitivity Channels A - F: 4 - 16 Volts
Channels G - H: 4 - 16 or 8 - 32 Volts
Input impedance RCA / Cinch -
Input impedance highlevel 9 - 33 Ohms with ADEP.3
Outputs 10 x Speaker output
1 x RCA / Cinch
1 x Remote Out
Output voltage RCA / Cinch 3 Volts
Frequency response 10 Hz - 22,000 Hz
DSP resolution 64 Bit
DSP power 295 MHz (1.2 billion MAC operations/second)
Sampling rate 48 kHz
DSP type Audio signal processor
Signal converters A/D: BurrBrown
D/A: BurrBrown
Signal-to-noise ratio digital input 105 dB (A-weighted)
Signal-to-noise ratio analog input 103 dB (A-weighted)
Distortion (THD) < 0.03 %
Damping factor > 100
Operating voltage 10.5 - 18 Volts (max. 5 sec. down to 6 Volts)
Power rating DC 12 V ⎓ 60 A max.
Idle current 500 mA
Max. remote output current 500 mA
Operating temperature range -40° C to +70° C
Fuse 2 x 25 A LP-Mini-fuse (APS)
Additional features Class GD technology with dynamically controlled
power supply, 32 Bit CoProcessor, ADEP.3 circuit, Start-Stop capability, Smart Control Port, USB, MEC slot, Auto Remote switch, galvanically isolated Line Out
Dimensions (H x W x D) 46 x 145 x 163 mm /
1.81 x 5.71 x 6.42"
$0.00
/
Tax included. Shipping calculated at checkout.

This site is protected by hCaptcha and the hCaptcha Privacy Policy and Terms of Service apply.

You may also like

Recently viewed